Festool Power box User Manual download pdf (Page 19)

EAA



Insert the other end of the blue hose into the

connector

[5-1]



Grease the bottom section of the aluminium

pipe and slide into the Y-piece on the EAA

[5-8]

up to the stop.



Tighten the two screws

[5-9]

on the gripper

clamp to a tightening torque of 6 Nm. The EAA is

now seated securely on the aluminium pipe.

Connect all the hoses in the EAA (see chapter 8

"Connections in the EAA") before following the wall

mounting instructions described below.



Secure the rear panel to the EAA using the

screws supplied.



Attach the lower retaining rail to the wall first

(see Fig.

[8a]

). If the wall is made of concrete,

use the enclosed dowels.

Note:

leave 1 m of

clearance between the panel and the ceiling.



Insert the EAA into the lower retaining rail from

above. The hooks must engage in the EAA hous-

ing.



Attach the upper retaining rail

[8b-1]

to the

EAA. The hooks must engage in the EAA hous-

ing.



Attach the upper retaining rail to the wall (see

Fig.

[8b]

). If the wall is made of concrete, use

the enclosed dowels.



Attach the adapter

[8b-2]

to connect the suction

hose to the aluminium pipe. Alternatively, you

can extend the aluminium pipe by attaching a

plastic pipe (install with antistatic discharge) or

steel pipe for extraction systems, and then at-

tach the adapter afterwards.



This version does not allow the attachment of

hose holders (see chapter 8.4).

7.3 Ceiling installation

The assembly set contains:

– Cable set (mains power and control cable, 2.5 m

long)

– Compressed air line (2.5 m long)

– Aluminium pipe for suspending the EAA

–Hydraulic pipe

– 2 x clamps with rivet

–2 x cable clips

–Bracket

Procedure



The aluminium pipe is 1.6 m in length on deliv-

ery. The pipe can be shortened at the open end

if necessary. We recommend adapting the

length of the pipe so that the tool holder

[1-1]

on the EAA is positioned at forehead height.

Al-

ways deburr the aluminium pipe after cutting

to length!



Remove the rear panel of the EAA.



Grease the bottom section of the aluminium

pipe and slide into the Y-piece on the EAA

[5-8]

up to the stop.



Tighten the two screws

[5-9]

on the gripper

clamp to a tightening torque of 6 Nm. The EAA is

now seated securely on the aluminium pipe.



Secure the bracket

[9-2]

to the ceiling via the

four holes

[9-1]

. Use fasteners suitable for the

relevant building material (e.g. tie rods, dow-

els).

Skip to chapter 8 "Connections in the EAA".

8 Connections in the EAA

8.1 Connecting the control cable



Wind the excess cable onto the holder

[5-10]



Place the flat seal supplied

[10-1]

over the ca-

ble connector

[5-2]

in the EAA.



Insert the contact box

[10-2]

into the cable con-

nector

[5-2]

and tighten the screw

[10-3]



Secure the control cable under the strain relief

on the EAA

[5-3]

8.2 Connecting the mains cable



Wind the excess cable around the ridged section

[5-6]



Place the flat seal supplied

[10-6]

over the con-

tact box

[5-7]

in the EAA.



Insert the contact box

[10-5]

into the cable con-

nector

[5-7]

and tighten the screw

[10-4]



Secure the mains cable under the strain relief

on the EAA

[5-4]



Plug the mains cable on the EAA into an earthed

socket with a 16 A fuse.

Exception:

If the connected dust extractor is

from another manufacturer, a different configu-

ration may be more appropriate - see chapter

9.1 "Mobile dust extractor".



On country versions GB, CH and DK, the plug on

the mains cable for the EAA/ASA must be re-

moved and replaced with the accompanying re-

wirable plug.

Note:

only trained and qualified

electricians are authorised to perform this

work!

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 163 164

Festool Power box User Manual Page 19

Comments to this Manuals

Festool Power box User Manual Page 19

Comments to this Manuals

Related products and manuals for Power tools Festool Power box