Festool C12 User Manual download pdf (Page 5)

Chuck BF-FX

The chuck is used to clamp drills and bits.

Fitting:

- Place the chuck on the drill spindle (2.5) and

twist until the hexagon key (2.4) of the chuck

latches into the hexagon socket of the drill

spindle.

- Pull the unlocking ring (2.3) forwards, press the

chuck onto the drill spindle up to the stop and

release the unlocking ring.

Removal:

- Pull the unlocking ring forwards and remove

the chuck.

Changing tools:

- Turn the clamping sleeve (2.2) anti-clockwise

to open the clamping jaws (2.1)

(Note: the spindle is automatically locked when

the machine is switched off).

- Insert the tool into the chuck.

- Clamp the tool by turning the clamping sleeve

clockwise. Always make sure that the tool is

clamped centrally in the chuck.

Angle attachment DD-AS

The angle attachment permits work (drilling,

screwing) vertical to the machine’s longitudinal

axis.

Fitting:

- Place the angle attachment on the drill spindle

and turn until it catches in the desired position

(Note: The angle attachment can be ﬁ tted in

16 different angle settings).

- Lock the angle attachment by turning the fas-

tening ring (2.7) tightly clockwise.

Removal:

- Turn the fastening ring anti-clockwise up to the

stop and remove the angel attachment.

Fitting / removal of chuck on angle attach ment:

The chuck is ﬁ tted on the shaft (2.6) of the angle

attachment in the same way as on the drill spindle

of the machine.

Eccentric attachment DD-ES

The eccentric attachment is used to hold bits. It

allows screwing close to edges.

Fitting / removing the eccentric attach ment:

The eccentric attachment is ﬁ tted / removed in

the same was as the angle attachment (see DD-

AS).

Changing tools:

Pull the unlocking ring (2.8) back and remove the

tool and/or insert the new tool.

CENTROTEC WH-CE toolholder

The CENTROTEC toolholder enables rapid changes

of tools with CENTROTEC shafts.

Danger of injury! When changing

tools, handle the tool and its sharp cutters with

special care and wear protective gloves, if neces-

sary.

Do not ﬁ t CENTROTEC tools at the

round shaft section in a conventional chuck to

prevent damage to the shaft.

Fitting

- Pull the release ring (2.11) forwards, place the

toolholder as far as it will go on the drill spindle

(2.5) and let go of the release ring.

Removal

- Pull the release ring forwards and take off the

toolholder.

Changing tools

- To insert or remove a tool with CENTROTEC

shaft, pull the green release ring (2.10) back.

On inserting the tool, turn it until its hex shank

arbour (2.9) locks in place in the hexagonal

shank of the drill spindle, and push the tool into

the toolholder as far as it will go.

Tool holding ﬁ xture in the drill

spindle

Bits can be ﬁ tted directly in the hexagon socket

holder of the drill spindle (2.5) to make the ma-

chine lighter and shorter.

Charge battery pack

To load the battery pack, push it into the holder

(3.1) on the charger up to the stop. Perform this

in reverse to remove the battery pack from the

charger.

The battery type used (NiCd or NiMH) is detected

automatically. Charging is controlled by a micro-

processor.

If a warm NiMH battery pack (>37° C) is insert-

ed, charging will only be carried out at a lower

charge current. In this case, the charging time is

extended.

1 2 3 4 5 6 7 8 9 10 ... 19 20

Comments to this Manuals

No comments

Festool C12 User Manual Page 5

Comments to this Manuals